Aluminium Treatment — HPDC Flux

High-Pressure Die Casting Flux

High-pressure die casting flux is formulated specifically for the holding furnaces and holding pots of aluminium HPDC operations, where the high metal velocity during injection demands a clean, oxide-film-free melt — any oxide entrained during injection is fragmented through the casting and cannot be recovered, causing surface defects, porosity, and cold-shuts.

HPDC is the most demanding aluminium casting process from a melt quality perspective: metal injected at 40 to 80 m/s through a narrow gate fragments any oxide films into particles distributed throughout the casting, causing blisters after T6 heat treatment and sub-surface porosity that fails leak testing. The holding furnace between the melting furnace and the shot sleeve is the last opportunity to clean the metal before injection. CFC Egypt's EGYFLUX 300 is formulated for HPDC holding vessels — it protects the melt surface and cleans oxide inclusions from the metal in the cycle time available between shots, leaving minimal residue that could be transferred to the die or the casting.

Fiyat teklifi isteyin All aluminium treatment

01

HPDC Flux in Aluminium Die Casting

HPDC flux is used in holding furnaces, holding pots, and ladles across aluminium high-pressure die casting operations — from automotive structural castings to consumer electronics enclosures.

Automotive Structural HPDC

Automotive structural die castings — shock towers, A-pillars, battery housing frames, and body nodes — are produced in aluminium alloys and subject to x-ray inspection, leak testing, and T6 heat treatment. Any oxide film entrained during injection creates internal defects that cause blistering after heat treatment or failure in pressure testing. HPDC flux applied in the holding furnace before each production run is an essential process control for achieving the melt cleanliness required for zero-defect structural casting.

Engine & Powertrain Components

Engine components cast by HPDC — cylinder blocks, oil pans, gearbox cases, and water pump housings — must be pressure-tight and dimensionally accurate. Sub-surface oxide inclusions cause leak paths through the casting wall that are only discovered during pressure testing after machining. Consistent flux treatment of the holding furnace metal before each shift minimises the oxide inclusion burden and reduces the rate of castings failing pressure test — a direct manufacturing cost saving.

EV Battery Enclosures & Structural Nodes

Electric vehicle battery enclosures are among the most demanding HPDC applications — large, thin-walled, structurally critical castings that must pass stringent leak and crash tests. The trend toward gigacasting — producing entire underbody sections in a single HPDC shot — amplifies the importance of melt cleanliness, because oxide defects in a large structural casting cannot be reworked or machined out. HPDC flux treatment of the large holding furnaces feeding gigacast machines is a critical process control point.

General Engineering & Consumer HPDC

General engineering castings — pump bodies, valve housings, electronic enclosures, and fittings — are produced in high volume by HPDC and require consistent surface quality and dimensional repeatability. While x-ray inspection is not always specified for these parts, oxide inclusions cause surface blemishes on cosmetically visible faces and weaken castings that are drilled and tapped. HPDC flux is a low-cost process control that improves surface quality and reduces scrap rates across all high-volume aluminium die casting production.

02

CFC HPDC Flux Product

EGYFLUX 300 — high-pressure die casting flux for aluminium holding furnaces and pots, delivering clean metal for injection without flux residue contamination.

03

Frequently Asked Questions

Technical questions on HPDC melt quality requirements and how flux treatment supports them.

In HPDC, molten aluminium is injected into the die at high speed — creating intense turbulence that fragments any oxide films present in the metal into tiny particles distributed throughout the casting. These oxide film fragments cause surface blisters after heat treatment, sub-surface porosity that fails pressure testing, and cold-shuts in thin sections. Gravity casting at low velocity allows some oxide to float to the riser. HPDC gives oxide films no opportunity to be removed after injection, so they must be eliminated before the metal enters the shot sleeve.

HPDC flux is applied in the holding furnace or holding pot that supplies metal to the die casting machine shot sleeve. The holding vessel sits at temperature between shots, and its surface builds up oxide during the hold period. Flux is applied on a regular per-shift or per-tonnage basis to protect the melt surface and clean oxide from the bath. The flux is worked in lightly and the resulting dross skimmed before metal is ladled or pumped to the machine.

HPDC flux is formulated to provide effective melt cleaning in the smaller volumes and shorter hold times typical of die casting holding furnaces and pots, leaving little or no flux residue in the melt that could contaminate the shot and damage the die or cause injection defects. Standard covering flux would either over-flux a small holding pot or leave residues transferred into the die with the metal. The HPDC formulation balances covering, cleaning, and low-residue performance for the specific demands of die casting operation cycles.

CFC Egypt manufactures EGYFLUX 300 as the high-pressure die casting flux for aluminium. It is formulated specifically for HPDC holding furnaces and holding pots, where the high-velocity metal injection demands a clean, oxide-free melt. Contact CFC for dosing guidance, treatment frequency, and application procedure recommendations for your specific HPDC machine type and holding furnace capacity.

04

Related Aluminium Treatment Products

Other CFC aluminium flux products that support die casting melt quality.

Alüminyum İşlem

Degassing Flux

Powder flux that removes dissolved hydrogen from the melt before pouring, reducing gas porosity.

Alüminyum İşlem

Demagging Flux

Reactive flux that reduces excess magnesium, preventing hot shortness in HPDC alloys.

Alüminyum İşlem

Covering, Drossing & Cleaning Fluxes

Multi-function flux powders and granules for melt surface protection and metal recovery.

All Types

Aluminium Treatment Overview

Browse all twelve aluminium treatment product categories from CFC Egypt.

Bizimle konuşun

Looking to reduce oxide-related defects in your HPDC production?

Tell us your HPDC machine type, holding furnace capacity, alloy grade, and current quality challenges — blisters, porosity, cold-shuts, or die erosion. Our technical team will recommend the right EGYFLUX 300 treatment procedure and dosing rate for your operation.

Fiyat teklifi isteyin Browse catalogue